Asonator Serie Asotub

ASONATOR® springs of ASOTUB series are designed for the isolation of vibrations and structural frequencies produced by any type of hanging mass: pipes, hoses, hanging equipment. They integrate the ISOTOP SN/Z and SD/Z series with higher single loads. The isolation of the structural frequencies is possible thanks to the interposition of dissipative material between the spring and the upper plate. The metal components of the different versions are treated for adequate resistance to environmental corrosion.

Asonator serie IFB e IFB-D

ASONATOR® series IFB and IFB/D withstand single loads up to 416,000 N. They are made of steel springs with high transverse rigidity and a high safety factor against breakage. The casing and the connecting elements are made of welded steel and, for a long resistance to corrosion, they are subjected to lacquering. The ASONATOR® IFB and IFB/D are equipped with steel screws that act as preload tension rods and are supplied preloaded with a slightly lower deformation than that corresponding to the recommended minimum load. The IFB/D version has a viscous damping element to reduce the resonance effects and further attenuate the vibrations.

Asonator serie 600

The ASONATOR® series 100 antivibration mounts, consist of a single steel helical spring placed between two plates. In the two spring-plate connections are interposed elements in synthetic material dissipating  the structural frequencies transmissible by solid way. Each metal part is subjected to anticorrosive treatment. They can realize high deflections under load, and therefore low natural frequencies and consequently high degree of insulation.

Asonator serie U

The ASONATOR® series U are steel spring vibration damping systems for loads from 100 kg up to 1 ton. The robust structure is made of welded steel and treated to withstand environmental corrosion. The base plate has two slots for fixing to the supporting surface.

Asonator serie 100

The ASONATOR® series 100 antivibration mounts, consist of a single steel helical spring placed between two plates. In the two spring-plate connections are interposed elements in synthetic material dissipating  the structural frequencies transmissible by solid way. Each metal part is subjected to anticorrosive treatment. They can realize high deflections under load, and therefore low natural frequencies and consequently high degree of insulation.

Asonator serie E100

The E100 series ASONATOR® antivibration mounts consist of a single steel helical spring placed between two plates. In the two spring-plate connections are interposed elements in synthetic material dissipating the structural frequencies transmissible by solid way. Each metal part is subjected to anticorrosive treatment. They can realize high deflections under load, and therefore low natural frequencies and consequently high degree of insulation.

Molle Serie SD

Isotop® SD steel spring vibration isolators consist of two metal plates with M10 internal thread and a cylindrical screw spring. Height adjustment is done via a threaded rod M10 with three nuts and three locking washers for level adjustment and weight distribution. Corrosion protection: galvanized or cataphoresis coated (KTL) as option.
Isotop® SD elements can reach a natural frequency down to approx. 3,0 Hz.

Molle Serie MSN-Z

Isotop® MSN/Z, MSN/Z-LC and SD/Z are tension elements consisting of a spring element, connection nuts for threaded rods and either a rectangular tube housing or open steel sheet housing (LC-model). All Isotop® MSN/Z and MSN/Z-LC have connection thread M8 and Isotop® SD/Z has connection thread M10. As an option, all tension elements are also available with a damping core inside. Applications are: suspension elements from ceilings and steel constructions; source isolation of ceiling-hung ventilators, fans, extractors, air conditioners, pipe lines etc. Receiver isolation of sensitive electronic measuring equipment in refrigeration, air conditioning and ventilation as well as in pipe line and ceiling construction.

Molle Serie BL-SD DSD e BL-MSN

lsotop® BL block elements (SD, DSD & MSN) consist of two steel plates and spring elements with or without damping. The number of spring elements depends on the load.
All elements are cataphoresis coated, which guarantees high corrosion resistance. To prevent slipping, PU footplates and/or pressure plates (anti-slip plates) can also be fitted. Special designs are available on request.

Molle Serie MSN

Isotop® MSN steel spring vibration isolators consist of two metal plates with M8 internal thread and a cylindrical screw spring. The metal plates and the screw spring are inseparably connected with a special 2-component compound. On request, MSN steel spring can be galvanized or cataphoresis coated with RAL 9005 (deep black).
Isotop® MSN elements can gain a natural frequency down to approx. 3,5 Hz and are manly used for: compressors, extractors, small ventilators, pumps, emergency power units.

© Pantecnica® S.p.A. | Via Magenta 77/14A - 20017 Rho (MI) | C.F. e P.IVA IT 06914490153 | Legal Notice | Privacy Policy | Cookie Policy